diff --git a/docs/delta/6/6.md b/docs/delta/6/6.md index bac56d0..d7ab4b1 100644 --- a/docs/delta/6/6.md +++ b/docs/delta/6/6.md @@ -35,26 +35,26 @@ title: Heated Bed Assembly ### Assembly process -1.Pass the M4*8 round head screw through the heated bed mount and screw it into the threaded steel ball，tighten as shown in the figure. +1. Pass the M4*8 round head screw through the heated bed mount and screw it into the threaded steel ball，tighten as shown in the figure. ![image.webp](1.webp){.img1} ![image.webp](2.webp){.img1} ![image.webp](3.webp){.img1} -2.Use two M3*14 cup-head screws to pass through the heated bed mount and screw on two drop-in t-nuts, type 20-M3, do not tighten them completely, just tighten them, as shown in the picture. +2. Use two M3*14 cap-head screws to pass through the heated bed mount and screw on two t-nuts, type 20-M3, do not tighten them completely, just tighten them, as shown in the picture. ![image.webp](4.webp){.img1} ![image.webp](5.webp){.img1} -3.Secure to the short aluminum profile, note the position of the two drop-in t-nuts, type 20-M3, they should be engaged in the grooves of the short profile, but do not tighten them completely, as shown in the picture. +3. Secure to the short aluminum profile, note the position of the two t-nuts, type 20-M3. They should be engaged in the grooves of the short profile, but do not tighten them completely, as shown in the picture. ![image.webp](7.webp){.img1} ![image.webp](8.webp){.img1} -4.Adjust the position of the heated bed mount, so that the edge of the short aluminum profile is an equal distant from both sides of the heated bed mount, as shown in the figure. +4. Adjust the position of the heated bed mount, so that the edge of the short aluminum profile is an equal distant from both sides of the heated bed mount, as shown in the figure. ![image.webp](9.webp){.img1} -5.The installation methods for the other two groups are the same. +5. The installation methods for the other two groups are the same. ![image.webp](10.webp){.img1} -6.Place the heated bed aluminum plate onto the heated bed mounts, as shown in the figure. +6. Place the heated bed aluminum plate onto the heated bed mounts, as shown in the figure. ![image.webp](11.webp){.img1} ![image.webp](12.webp){.img1} @@ -63,7 +63,7 @@ title: Heated Bed Assembly Note the front and back of the heated bed aluminum plate ; the counterbore hole should face upwards. ![image.webp](14.webp){.img1} -7.Fine-tune the position of the heated bed aluminum plate and the heated bed mounts so that all three holes in the heated bed aluminum plate can fit into the threaded steel ball heads of the heated bed mounts. +7. Fine-tune the position of the heated bed aluminum plate and the heated bed mounts so that all three holes in the heated bed aluminum plate can fit into the threaded steel ball heads of the heated bed mounts. !!! warning "warning" After ensuring that all three holes in the heated bed aluminum plate can fit into the blind ball heads on the heated bed mounts. @@ -102,11 +102,11 @@ title: Heated Bed Assembly ### Assembly process -1.Use two M3*8 countersunk screws to pass through the heated bed baffle, and screw on two type 20 - M3 drop-in t-nuts, do not tighten them completely, just tighten them, as shown in the picture . +1. Use two M3*8 countersunk screws to pass through the heated bed baffle, and screw on two type 20 - M3 t-nuts, do not tighten them completely. Just tighten them, as shown in the picture . ![image.webp](16.webp){.img1} ![image.webp](17.webp){.img1} -2.Secure the heated bed baffles to the short aluminum profile. +2. Secure the heated bed baffles to the short aluminum profile.
- :material-clock-fast:{ .lg .middle } __Tips__ @@ -140,11 +140,11 @@ title: Heated Bed Assembly ### Assembly process -1.Pass two M3*8 countersunk screws through the rear heated bed baffle and screw on two drop-in type20 - M3 boat nuts, do not tighten them completely, just tighten them as shown in the picture. +1. Pass two M3*8 countersunk screws through the rear heated bed baffle and screw on two drop-in type20 - M3 boat nuts, but do not tighten them completely. Just tighten them as shown in the picture. ![image.webp](20.webp){.img1} ![image.webp](21.webp){.img1} -2.Secure the rear heated bed baflle to the short aluminum profile. +2. Secure the rear heated bed baflle to the short aluminum profile.
- :material-clock-fast:{ .lg .middle } __Tips__ @@ -185,29 +185,29 @@ title: Heated Bed Assembly ### Assembly process -1.Use an M3*10 cap-head screw to pass through the heated bed aluminum plate and the heated bed thermal fuse, and tighten it with a self-locking nut, as shown in the figure. +1. Use an M3*10 cap-head screw to pass through the heated bed aluminum plate and the heated bed thermal fuse, and tighten it with a self-locking nut, as shown in the figure. ![image.webp](23.webp){.img1} !!! Warning "Screw Fixing" - Note the orientation of the M3*10 cap-head screws when installing the heated bed aluminum plate; the counterbore hole should face upwards. + Note the orientation of the M3*10 cap-head screws when installing the heated bed aluminum plate. The counterbore hole should face upwards. ![image.webp](33.webp){.img1} -2.Connect the thermal fuse cable as shown in the figure. +2. Connect the thermal fuse cable as shown in the figure. ![image.webp](24.webp){.img1} -3.Attach the mains powered silicone heater pad to the heated bed aluminum plate, ensuring that it is centered on the plate and the cable exit point is close to the heated bed thermal fuse, as shown in the figure. +3. Attach the mains powered silicone heater pad to the heated bed aluminum plate, ensuring that it is centered on the plate and the cable exit point is close to the heated bed thermal fuse, as shown in the figure. ![image.webp](25.webp){.img1} ![image.webp](26.webp){.img1} -4.Connect the thermal fuse cable of the silicone heating pad to the fuse cable of the heated bed, as shown in the figure. +4. Connect the thermal fuse cable of the silicone heating pad to the fuse cable of the heated bed, as shown in the figure. ![image.webp](27.webp){.img1} ![image.webp](28.webp){.img1} -5.Reverse the heated aluminum bed plate and attach the magnetic sticker to it, as shown in the picture. +5. Reverse the heated aluminum bed plate and attach the magnetic sticker to it, as shown in the picture. ![image.webp](29.webp){.img1} ![image.webp](30.webp){.img1} -6.Mount the PEI build sheet onto the heated aluminum plate as shown in the figure +6. Mount the PEI build sheet onto the heated aluminum plate as shown in the figure ![image.webp](31.webp){.img1} ![image.webp](32.webp){.img1}