diff --git a/arch/arm64/boot/dts/exynos/google/gs201-panther.dts b/arch/arm64/boot/dts/exynos/google/gs201-panther.dts index d3e061a5b6..8c42276bf2 100644 --- a/arch/arm64/boot/dts/exynos/google/gs201-panther.dts +++ b/arch/arm64/boot/dts/exynos/google/gs201-panther.dts @@ -4,13 +4,14 @@ * * USB (NCM + ACM), the cluster watchdogs from gs201.dtsi, a * simple-framebuffer on the buffer ABL leaves DPP0 scanning out, UFS, the - * three keys, and the touch rails on the main PMIC. The panel driver, - * touch and the GPU stay disabled. + * three keys, the touchscreen with its rails on the main PMIC, the GPU and + * the haptics. The panel driver stays disabled. */ /dts-v1/; #include +#include #include "gs201.dtsi" / { @@ -25,7 +26,7 @@ chosen { /* ABL requires bootargs to exist; it appends its own after these. */ - bootargs = "console=tty0 panic=10 clk_ignore_unused pd_ignore_unused rdinit=/init omamobile.ufs-probe"; + bootargs = "console=tty0 panic=10 clk_ignore_unused pd_ignore_unused rdinit=/init omamobile.ufs-probe mem_sleep_default=s2idle"; #address-cells = <2>; #size-cells = <1>; ranges; @@ -127,12 +128,13 @@ interrupts = ; google,vgpio2ap-sysreg = <&sysreg_vgpio2ap>; wakeup-source; - status = "disabled"; regulators { - /* No voltage: the PMIC keeps the 1.8 V it holds. */ + /* Stock's 1.8 V, which ABL leaves programmed */ ldo25m: ldo25m { regulator-name = "vdd-ts"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; }; /* @@ -149,6 +151,11 @@ }; }; +&gpu { + /* No mali-supply: the G3D rails follow the PMU power domain and ACPM. */ + status = "okay"; +}; + &usbdrd31_phy { status = "okay"; }; @@ -165,3 +172,86 @@ &ufs_0_phy { status = "okay"; }; + +/* + * Haptics: Cirrus Logic CS40L26A at 0x43 on PERIC0 USI8 (Google's I2C bus + * 8), INTb on gpa8-1, RESET on gpp24-3, as on the Pixel 7 Pro. Boost and + * actuator values are the stock ones, the same as the Pixel 7 Pro's + * (bst-ipk 2.5 A, bst-ctl 11 V, f0 145 Hz, ReDC 13 ohm in the live tree). + * The bus pins are on PERIC0 (gpp16-0/1). + */ +&pinctrl_far_alive { + hapt_amp_irq: hapt-amp-irq-pins { + samsung,pins = "gpa8-1"; + samsung,pin-function = ; + samsung,pin-pud = ; + samsung,pin-drv = ; + }; +}; + +&pinctrl_peric0 { + status = "okay"; +}; + +&pinctrl_peric1 { + hapt_amp_rst: hapt-amp-rst-pins { + samsung,pins = "gpp24-3"; + samsung,pin-function = ; + samsung,pin-pud = ; + samsung,pin-drv = ; + }; +}; + +&usi8 { + samsung,mode = ; + status = "okay"; +}; + +&hsi2c_8 { + clock-frequency = <400000>; + status = "okay"; + + haptics: haptic-driver@43 { + compatible = "cirrus,cs40l26a"; + reg = <0x43>; + interrupts-extended = <&gpa8 1 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpp24 3 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&hapt_amp_irq &hapt_amp_rst>; + pinctrl-names = "default"; + cirrus,boost-peak-microamp = <2500000>; + cirrus,boost-ctl-microvolt = <11000000>; + cirrus,lra-f0-hz = <145>; + cirrus,lra-redc-micro-ohms = <13000000>; + }; +}; + +/* + * Touchscreen: a FocalTech FT3658 on USI0 SPI, wired as the Pixel 7 Pro's + * S3908 (chip select gpp20-3, interrupt gpa7-0, reset gpp23-2). + */ +&usi0 { + samsung,mode = ; + status = "okay"; +}; + +&spi_0 { + pinctrl-0 = <&spi0_bus &spi0_miso &spi0_cs_gpio>; + cs-gpios = <&gpp20 3 GPIO_ACTIVE_LOW>; + num-cs = <1>; + status = "okay"; + + touchscreen@0 { + compatible = "focaltech,ft3658"; + reg = <0>; + spi-max-frequency = <10000000>; + interrupt-parent = <&gpa7>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpp23 2 GPIO_ACTIVE_LOW>; + vdd-supply = <&ldo25m>; + avdd-supply = <&ldo26m>; + pinctrl-0 = <&ts_irq &ts_reset>; + pinctrl-names = "default"; + touchscreen-size-x = <1080>; + touchscreen-size-y = <2400>; + }; +};