RobotCharacterization/robotconfig.py at master · Techbrick/RobotCharacterization · GitHub

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
{
    # Ports for motors
    # If doing drive test, treat this as the left side of the drivetrain
    "motorPorts": [1,2],
    # Only if you are doing drive (leave empty "[]" if not)
    "rightMotorPorts": [6,7],
    # Class names of motor controllers used.
    # 'WPI_TalonSRX'
    # 'WPI_VictorSPX'
    # 'WPI_TalonFX'
    # If doing drive test, treat this as the left side of the drivetrain
    "controllerTypes": ['WPI_TalonSRX', 'WPI_VictorSPX'],
    # Only if you are doing drive (leave empty "[]" if not)
    "rightControllerTypes": ['WPI_TalonSRX','WPI_VictorSPX'],
    # Set motors to inverted or not
    # If doing drive test, treat this as the left side of the drivetrain
    "motorsInverted": [True,True],
    # Only if you are doing drive (leave empty "[]" if not)
    "rightMotorsInverted": [True,True],
    # Encoder edges-per-revolution (*NOT* cycles per revolution!)
    # For the CTRE Mag Encoder, use 4096 (4 * 1024 = 4096)
    "encoderEPR": 4096,

# Third stage on the gearbox is 30:54, using 6" wheels.
# Vexpor gearbox spins the mag-encoder 3x faster
# than the 2nd stage output shaft.

    # Gearing accounts for the gearing between the encoder and the output shaft
    "gearing": .6,
    # Encoder ports (leave empty "[]" if not needed)
    # Specifying encoder ports indicates you want to use Rio-side encoders
    # If doing drive test, treat this as the left side of the drivetrain
    "encoderPorts": [],
    # Only if you are doing drive (leave empty "[]" if not)
    "rightEncoderPorts": [],
    # Set to True if encoders need to be inverted
    # If doing drive test, treat this as the left side of the drivetrain
    "encoderInverted": False,
    # Only if you are doing drive (set to False if not needed)
    "rightEncoderInverted": False,
    # ** The following is only if you are using a gyro for the DriveTrain test**
    # Gyro type (one of "NavX", "Pigeon", "ADXRS450", "AnalogGyro", or "None")
    "gyroType": "NavX",
    # Whatever you put into the constructor of your gyro
    # Could be:
    # "SPI.Port.kMXP" (MXP SPI port for NavX or ADXRS450),
    # "SerialPort.Port.kMXP" (MXP Serial port for NavX),
    # "I2C.Port.kOnboard" (Onboard I2C port for NavX),
    # "0" (Pigeon CAN ID or AnalogGyro channel),
    # "new WPI_TalonSRX(3)" (Pigeon on a Talon SRX),
    # "" (NavX using default SPI, ADXRS450 using onboard CS0, or no gyro)
    "gyroPort": "SPI.Port.kMXP",
}